• True RMS (True root-mean-square value)

  True RMS value. AC current and voltage of a non-sine wave can be measured by true RMS values.

• Dual Display

  Allows simultaneous reading.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Temperature measurement

  Temperature can be measured using a probe.

• 4-20mA%

  4-20mA for sending instrumentation signals. Expresses the current loop of 4mA as 0% and 20mA as 100%

• dBm

  Scaling of voltage values is performed according to the reference impedance into dBm. Convenient for use with audio equipment.

• peak hold

  The peak value like in-rush current is indicated. The minimum pulse width capturable differs according to models.

• Low-pass filter

  Low-pass filter cuts current value of high frequency.

• Auto power save

  The display disappears to bring the device into the power-save state when a certain time has passed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• MAX / MIN / AVG

  The maximum value, the minimum value and the average value are displayed or recorded. The recorded value can be seen later on the display.

• Backlight

  Allows indicator reading in a dark place.

• USB conneciton

  Data can be output by connecting to the USB port of a PC.

• Temperature measurement with PC Link

  Temperature can be measured using the optional probe and PC Link software. (T-300PC is necessary.)

Move your mouse pointer over or click on an icon to see a description of the icon.

• True RMS (True root-mean-square value)

  True RMS value. AC current and voltage of a non-sine wave can be measured by true RMS values.

• Dual Display

  Allows simultaneous reading.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Temperature measurement

  Temperature can be measured using a probe.

• EF function

  Non-contact AC voltage detection

• peak hold

  The peak value like in-rush current is indicated. The minimum pulse width capturable differs according to models.

• Auto power save

  The display disappears to bring the device into the power-save state when a certain time has passed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• MAX / MIN / AVG

  The maximum value, the minimum value and the average value are displayed or recorded. The recorded value can be seen later on the display.

• Backlight

  Allows indicator reading in a dark place.

• USB conneciton

  Data can be output by connecting to the USB port of a PC.

• Temperature measurement with PC Link

  Temperature can be measured using the optional probe and PC Link software. (T-300PC is necessary.)

Move your mouse pointer over or click on an icon to see a description of the icon.

• True RMS (True root-mean-square value)

  True RMS value. AC current and voltage of a non-sine wave can be measured by true RMS values.

• Dual Display

  Allows simultaneous reading.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Temperature measurement

  Temperature can be measured using a probe.

• peak hold

  The peak value like in-rush current is indicated. The minimum pulse width capturable differs according to models.

• Automatic Measurement for DCV/ACV/Ω

  Measurement function of DCV/ACV/Ωcan be automatically selected.

• Logging

  The reading can be stored in the meter itself.

• Auto power save

  The display disappears to bring the device into the power-save state when a certain time has passed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• MAX / MIN

  The maximum value and the minimum value are displayed or recorded. The recorded value can be seen later on the display.

• Backlight

  Allows indicator reading in a dark place.

• USB conneciton

  Data can be output by connecting to the USB port of a PC.

• Temperature measurement with PC Link

  Temperature can be measured using the optional probe and PC Link software. (T-300PC is necessary.)

Move your mouse pointer over or click on an icon to see a description of the icon.

• Dual Display

  Allows simultaneous reading.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power save

  The display disappears to bring the device into the power-save state when a certain time has passed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• USB conneciton

  Data can be output by connecting to the USB port of a PC.

• Temperature measurement with PC Link

  Temperature can be measured using the optional probe and PC Link software. (T-300PC is necessary.)

Move your mouse pointer over or click on an icon to see a description of the icon.

• True RMS (True root-mean-square value)

  True RMS value. AC current and voltage of a non-sine wave can be measured by true RMS values.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Continuity check

  The LED lights up when the measuring object is electrically conducting.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• Backlight

  Allows indicator reading in a dark place.

• USB conneciton

  Data can be output by connecting to the USB port of a PC.

• Temperature measurement with PC Link

  Temperature can be measured using the optional probe and PC Link software. (T-300PC is necessary.)

Move your mouse pointer over or click on an icon to see a description of the icon.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

• USB conneciton

  Data can be output by connecting to the USB port of a PC.

• Temperature measurement with PC Link

  Temperature can be measured using the optional probe and PC Link software. (T-300PC is necessary.)

Move your mouse pointer over or click on an icon to see a description of the icon.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Continuity check

  The LED lights up when the measuring object is electrically conducting.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Battery check

  Battery voltage is measured and assessed by running a given current.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

• Backlight

  Allows indicator reading in a dark place.

Move your mouse pointer over or click on an icon to see a description of the icon.

• True RMS (True root-mean-square value)

  True RMS value. AC current and voltage of a non-sine wave can be measured by true RMS values.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Continuity check

  The LED lights up when the measuring object is electrically conducting.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Temperature measurement

  Temperature can be measured using a probe.

• Auto power save

  The display disappears to bring the device into the power-save state when a certain time has passed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

• Backlight

  Allows indicator reading in a dark place.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Temperature measurement

  Temperature can be measured using a probe.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• MAX

  The maximum value is displayed or recorded. The recorded value can be seen later on the display.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

Move your mouse pointer over or click on an icon to see a description of the icon.

• True RMS (True root-mean-square value)

  True RMS value. AC current and voltage of a non-sine wave can be measured by true RMS values.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Temperature measurement

  Temperature can be measured using a probe.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• MAX

  The maximum value is displayed or recorded. The recorded value can be seen later on the display.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity check

  The LED lights up when the measuring object is electrically conducting.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power save

  The display disappears to bring the device into the power-save state when a certain time has passed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Low power ohm

  Resistance is measured by applying voltage of approximately 0.4V or less on a measuring object. It is characterized by the fact that the semiconductor does not conduct at approximately 0.4V or less even in forward direction.

Move your mouse pointer over or click on an icon to see a description of the icon.

• True RMS (True root-mean-square value)

  True RMS value. AC current and voltage of a non-sine wave can be measured by true RMS values.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• EF function

  Non-contact AC voltage detection

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Backlight

  Allows indicator reading in a dark place.

Move your mouse pointer over or click on an icon to see a description of the icon.

• Max
  100A

• DC / AC measurable

  Both ACA and DCA are measurable.

• Frequency

  Expressed in the unit of Hz (hertz). Commercial frequency of 50Hz/60Hz can be measured.

• Capacitor

  Capacitor capacity (electrostatic capacity) is measured and expressed in the unit of F (farad), μF, etc.

• Duty cycle

  The duty cycle of repeating waveform is indicated on a percentage basis (%). It can be used for the analysis of control signals.

• Continuity buzzer

  The buzzer sounds when the measuring object is electrically conducting.

• Auto power off

  Power is automatically turned off when a certain time has elapsed after power-up. Some models have a function to cancel this function.

• Data hold

  A value indicated on the display is fixed. It is fixed even after the test lead is removed, and can be used as a record for reference purposes.

• Range hold

  The range is fixed in the measurement of varying voltage and current which is difficult to read in the auto range.

• Measurement of relative value

  A certain measured value is assumed as 0 and measured values after that are expressed by positive or negative values relative the value fixed as 0.

• MAX / MIN

  The maximum value and the minimum value are displayed or recorded. The recorded value can be seen later on the display.

Move your mouse pointer over or click on an icon to see a description of the icon.